Grow light questions, answered.
No questions match your search. Try a different word.
Light basics: PAR, PPFD, DLI and LUX
PPFD stands for Photosynthetic Photon Flux Density. It counts the photosynthetically useful photons landing on one square meter every second, measured in µmol/m²/s. It's how much light your plants are receiving right now. PPFD counts photons from 400 to 700 nm. Some newer charts count up to 750 nm and call it ePPFD, which adds far red. It's the single most useful number for dialing in a grow light, and it's the main reading the app shows.
PAR means Photosynthetically Active Radiation. It's the band of light that drives photosynthesis, traditionally 400 to 700 nm, which is roughly the same range your eyes see as color. Newer research extends this to 750 nm to include far red, a range called ePAR. PAR is the whole waveband. PPFD and PPF are the two ways we put a number on it, one at the canopy and one at the fixture.
ePAR stands for extended Photosynthetically Active Radiation. It widens the traditional PAR band from 400 to 700 nm out to 750 nm, adding the far-red photons between 700 and 750 nm. Far red was long left out of the count, but research, including work by Dr. Bruce Bugbee, shows those photons do drive photosynthesis when they work alongside shorter wavelengths, an effect known as the Emerson enhancement. Many modern LED grow lights now include far-red diodes, so stopping the count at 700 nm would undersell what they deliver. PPFD METER starts from a LUX reading, and LUX sensors see little far red, so a far-red add-on barely shows up in the number. The LUX to PPFD calculator shows PPFD and ePPFD side by side.
Try it: LUX to PPFD Calculator
DLI stands for Daily Light Integral. It's the total amount of PAR light your plants receive over a full day, measured in mol/m²/day. If PPFD is the instantaneous light intensity, DLI is the total light your plant receives across the whole day. A bright light running only a few hours can still leave a plant short of its daily light target, which is why PPFD METER tracks PPFD and DLI side by side.
Try it: PPFD to DLI Calculator
PPF stands for Photosynthetic Photon Flux. It's the total PAR photons a fixture pumps out every second, measured in µmol/s. PPF describes the light itself, no matter where it lands. PPFD describes how much of that light reaches one square meter of your canopy. A high PPF fixture spread too thin can still give you a weak PPFD, so canopy readings are what matter for your plants.
Try it: PPF to PPFD Calculator
They answer three different questions. PAR is the light plants can use, traditionally the 400 to 700 nm band. PPF is how much of that light the fixture emits in total, in µmol/s. PPFD is how much of it reaches your canopy per square meter each second, in µmol/m²/s. Growers care most about PPFD, because that's the light your plants are truly getting.
Try it: PPF to PPFD Calculator
PPFD is the light intensity reaching your plant right now, and DLI is the total light it receives over the whole day. PPFD measures light intensity in µmol/m²/s, while DLI adds it all up in mol/m²/day. A strong light running too few hours still leaves your plant short of its daily target. That's why PPFD METER tracks both at once.
Try it: PPFD to DLI Calculator
LUX measures brightness the way your eyes see it, weighted heavily toward green light. PPFD counts photons the way plants use them, from 400 to 700 nm. Your phone reads LUX. The app then converts that LUX into PPFD using a factor matched to your light source. The catch is that LUX alone can fool you. Two lights can read the same LUX but deliver very different PPFD, which is why growers work in PPFD, not LUX.
Because LUX is tuned to human vision, not photosynthesis. A basic LUX meter over-weights green light and under-counts the red and blue your plants use, so the same LUX reading means different PPFD under different lights. PPFD METER starts from LUX but applies the right conversion for your specific light source, turning a human-brightness reading into a plant-usable light reading.
Try it: LUX to PPFD Calculator
Yes, as long as you match the conversion to your light's spectrum. Lumens measure total brightness to the human eye, while PPF counts total PAR photons emitted each second in µmol/s. Because human eyes weight green light heavily and plants use red and blue too, a warm white LED, a cool white LED, and an HPS bulb deliver different PPF for the same lumen rating. Our Lumen to PPF calculator converts a fixture's rated lumens by light source, and our LUX to PPFD calculator does the same for readings at the canopy.
It's the unit for PPFD. It means micromoles of photons per square meter per second. A micromole is just a very large, countable batch of photons, since a single photon is far too small to work with. So a PPFD of 600 means roughly 600 micromoles of usable light photons are hitting each square meter of your canopy every second. You'll also see it written as µmol m⁻² s⁻¹, the way research papers and our calculators write it. It's the same unit. A minus power just means "per", so m⁻² is per square meter and s⁻¹ is per second, the same way km/h can be written km h⁻¹.
How the app measures
On Android, your phone's built-in ambient light sensor reads LUX, the same sensor that auto-adjusts your screen brightness. PPFD METER then converts that LUX to PPFD using a factor matched to your light source, whether that's sunlight, white LED, or HPS. Pick the right light type in the app so it applies the right conversion factor for your spectrum.
Try it: LUX to PPFD Calculator
Apple doesn't let apps read the iPhone's ambient light sensor, so on iOS PPFD METER uses the front camera as a light meter instead. It reads the camera's metadata and calculates LUX from it, then converts to PPFD and DLI. The app comes pre-calibrated for every supported iPhone, so it works out of the box. It never saves or uploads a photo, it only reads the metadata.
Yes. It's on Google Play and the App Store, with the same core features, math, and light source options on both. The main difference is how each phone senses light. Android uses the built-in ambient light sensor, and iPhone uses the front camera. Everything downstream, the PPFD, DLI, calibration, and PAR Maps, works the same way.
For most growers, no. A lab-grade quantum PAR meter can cost hundreds of dollars. PPFD METER turns a phone you already own into a horticultural light meter for free. It won't match a lab instrument to the decimal, but once you pick the right source and calibrate, it's accurate enough to make real decisions about hanging height, intensity, and coverage.
No. On Android, almost every phone already has the ambient light sensor the app needs. On iPhone, the front camera does the job, and a small paper diffuser made from office paper improves it. An optional Bluetooth light meter is available if you want more range and a faster sample rate, but nothing extra is required to get started.
Most phone sensors are good. It's mainly the low-end models that get noisy. Even uncalibrated, a phone is great at relative readings. It can tell you one spot is brighter than another, or that today beats last week, since that only takes consistency, not a perfect absolute number. Calibrate the sensor in the app and the absolute PPFD tightens up too, close enough to trust for real decisions. If you'd rather skip calibration altogether and remove any phone-to-phone variance, pair PPFD METER with an affordable Bluetooth LUX meter like the UNI-T UT383BT. It reads wirelessly, so you can drop it on the canopy, zip the tent shut, and check the number from your phone outside. It costs a fraction of a quantum PAR meter and is accurate enough to dial in a real grow.
Four things, mostly. Your phone sensor's quality and range, whether you picked the correct light source, whether you calibrated the built-in sensor, and your environment. Open tent doors, reflective walls, and a dirty sensor all shift the numbers. Get those right and the reading you see is one you can act on. The app doesn't promise lab accuracy it can't deliver.
Choosing a light source
Because the LUX to PPFD conversion depends on the spectrum of your light. An LED, an HPS, and a CMH can all read the same LUX but deliver different amounts of usable PPFD, since they emit different mixes of color. Telling the app which light you run lets it apply the right factor. Pick your source before you calibrate, since the source changes the numbers you'd be calibrating against.
Pick the color temperature that matches your fixture, for example LED 3000K, LED 4000K, or LED 6500K. PPFD METER covers the full range from warm 2700K to cool 6500K, plus versions with a 10% deep red (660 nm) boost, and options for HPS, CMH, halogen, fluorescent, and red, blue, and purple lights. When in doubt, check your fixture's spec sheet for its Kelvin rating and pick the closest match.
Try it: Kelvin Mixing Calculator
Average your diodes by their power ratio, then pick the closest option. Say your bar has 60 diodes at 3000K and 40 at 5000K. That's a 3 to 2 ratio. A quick power-weighted average gives 3800 K, while a true spectral mix in our Kelvin Mixing Calculator puts it closer to 3630 K, so picking the warmer LED 3500K option is the better match. The app's in-app source guide walks through the same 60/40 example using the power-weighted 3800 K figure and rounds to LED 4000K.
Try it: Kelvin Mixing Calculator
Use the matching white option with the +10% 660nm label. Deep red adds plenty of PPFD but very little LUX, so even about 10% of it by power changes the conversion. Find your closest white color temperature, then choose the version with the 660 nm boost, so the app counts those red photons.
Pick the closest Red, Blue, or Purple option in the source list. The Purple option assumes a 1 to 1 red to blue power ratio, and real fixtures vary a lot, so for these lights the app strongly recommends calibrating against a known PAR Map or manufacturer spec. That second calibration method corrects for whatever your actual red to blue balance is.
Reading the display
FPS is how many light samples your sensor delivers each second. Any value above 0 is usable. Some phones only report changes in light rather than a steady stream, so FPS can look jumpy or low, and that's normal. Higher FPS just means a smoother, more responsive reading. The Bluetooth UNI-T sensor can reach around 30 FPS, which is why it feels so much smoother than most built-in sensors.
Because a typical 240 watt grow light can push around 100000 LUX, which completely saturates a camera image and makes it useless for calculation. The ambient light sensor handles that brightness range comfortably, so on Android the app reads the sensor directly. On iPhone, where apps can't touch the ambient sensor, the camera is used carefully with its metadata instead of a saved image.
It helps a lot on iOS. Without one, the front camera's angular response is narrow, so it mostly reads light coming straight at it. A diffuser, just 75 to 80 gram white office paper taped snugly over the camera notch, widens and evens out that response, improves PAR Map accuracy, cancels most of the effect of a screen protector, and greatly reduces any need to calibrate. The app includes a short guide for crafting one.
Get the sensor close to the canopy, at the height your plants sit, and aim the screen or camera straight at the light. On iPhone with the naked front camera, about 20 to 40 cm from the canopy is the sweet spot the app is tuned for. Keep it level, hold steady, and take the reading where the plant would be, not where it's convenient to stand.
Start by cleaning the sensor area. Grease, dust, or a worn screen protector over the phone's light sensor or camera throws readings off more than people expect. Then confirm you picked the correct light source, and on the built-in sensor, that you've calibrated. Finally, make sure the sensor faces the light directly and sits near the canopy, not off to the side in shadow.
Press either volume button to pause and hold the current measurement. It freezes the number so you can read or record it without your hand shaking the value around. It's especially handy right after you close a tent door, when the light finally settles and you want to lock that reading in.
Profiles let you save up to five complete setups and switch between them with a tap. Each one keeps its own light source, threshold band, and daily lighting hours. Growers use them for different grow areas, or for different phases like seedling, veg, and flower, so you can jump from one to another without re-entering settings every time.
The displays change color based on the thresholds you set, so you can read your light at a glance without squinting at numbers. Set a low and high PPFD (and DLI) for the plant you're growing, say 300 to 500 during veg, and the display tells you instantly whether your light is below, inside, or above that target band. It's a traffic light for your canopy.
Calibration
It depends on what you want. If you're on the built-in sensor and you want accurate absolute PPFD numbers, yes, calibrate. If you only care about relative light distribution, which spot is brighter than another, you can skip it. The Bluetooth UNI-T sensor and the iPhone camera both come pre-calibrated, so calibration there is optional fine-tuning rather than a must.
You set a signed percentage that nudges every reading up or down to match a trusted reference. For example, +8% raises readings, and -4% lowers them. It's free and takes a minute. You can either match the app to a known LUX meter under a few different light levels, or match it to a published PAR Map or manufacturer spec by placing your lights exactly as in the reference.
Use this formula: (target divided by measured) minus 1.00. Say the app shows 1000 for a spot that should read 960. Then (960 divided by 1000) minus 1.00 equals -0.04, so you set -4%. The same spot now reads 960, with a small 'Calibration -4%' hint shown inside the display. Calibrate under bright light, since many sensors shift their sensitivity across the range.
No. PPFD METER stores a separate calibration factor for each sensor, so switching between the built-in sensor, the paper-diffuser mode on iPhone, and the UNI-T meter automatically applies the right one. You'll see a hint like 'Calibration -4%' inside the display so you always know which factor is active.
On Android, often yes. Here's a quick test. Set your grow lights to max, open the LUX Meter, and slowly move the phone from the canopy up toward the light. If the numbers climb smoothly toward roughly 150000 LUX, your sensor has the range you need. If it flatlines early or barely moves, it's saturating, and a Bluetooth sensor is the better path. The app includes a step-by-step 'Do I need calibration?' guide that walks through this. On iPhone the front camera comes pre-calibrated, so this test doesn't apply.
Bluetooth light meter
It's an affordable Bluetooth light meter that pairs with PPFD METER as an external sensor. It comes pre-calibrated and delivers up to about 30 readings per second, far smoother and more responsive than most built-in phone sensors. It's not a lab-grade instrument, but for the price it's a big step up in consistency, and it removes any phone-to-phone variance. Make sure you buy the UT383BT (with BT in the model name), not the standard UT383, which has no Bluetooth and cannot connect to the app.
Your phone is enough for most setups. Consider the UNI-T sensor if your built-in sensor saturates under bright light, if you want a faster and smoother sample rate, or if you'd rather skip calibration entirely. Its biggest advantage is convenience. Drop it on the canopy, zip the tent shut, and read the number on your phone from outside, no reaching in and blocking the light with your arm.
Grant the Bluetooth permission, put the UT383BT in discovery mode, then press Scan and pick the device from the list. If Bluetooth is off, the app tells you, and on Android it offers to turn it on. Once connected, the Sensor button icon changes to a Bluetooth symbol so you always know which sensor is active. There's an in-app guide covering each step.
Only to find and connect the Bluetooth sensor, never to track you. On Android 11 and below, Google requires location permission before any app can scan for Bluetooth devices. It's an operating system rule, not tracking. On Android 12 and up, the app uses the Nearby Devices permission instead. The app doesn't use or store your location. On iPhone, no location permission is needed at all. Our Privacy Policy has the details.
No. PPFD METER simply supports the UT383BT because it's an affordable, capable sensor that works well with the app. There's no partnership, sponsorship, or affiliation with UNI-T. The recommendation is purely practical. It's a good, affordable option if you want to step past your phone's built-in sensor.
PAR Maps and DLI Maps
Take readings in a grid across your canopy and PPFD METER draws the PAR Map for you. It gives you a clear picture of your light's spread and uniformity, so you can fix hot spots, fine-tune your hanging height, and compare fixtures. You just set the grow area size and grid layout, tap each cell to capture a reading, and the app fills in the map as you go.
A PAR Map is a grid of PPFD readings across your grow area's footprint. It shows exactly how your light lands: which spots are hot, which corners are dim, and how even the coverage really is. Growers use it to choose hanging height, position fixtures, compare one light against another, and set a baseline for efficiency. It turns a single center reading into a full picture of your canopy.
Press Create New, set your grow area size and pick a grid layout, then enter the hanging height, total watts drawn, and a name. Tap each grid cell to capture a reading, using the Capture button or the 9 second timer for hands-free capture, which gives you time to close the tent door if you're not on Bluetooth. With every capture the app updates Uniformity, Average PPFD, usable PPF, and Efficiency. You can always rename the map and edit its cell readings later, while the size, layout, hanging height, and watts stay fixed once created (start a new map if those change).
Uniformity is how evenly your light covers the canopy, shown as a percentage in each PAR Map. Even coverage means every plant gets a similar dose, so growth is consistent and no corner gets left in the dark or scorched by a hot spot. Low uniformity usually means your light is hung too low or your fixture is too small for the footprint. Raising the light or adding coverage evens things out.
Higher is better, and you'll rarely hit a perfect 100%. The app blends two common measures, the minimum-to-average and minimum-to-maximum ratios, into one percentage. Rather than chase a magic figure, use it to compare setups. Raise your light or spread your coverage and watch the number climb. A more uniform canopy grows more evenly.
A DLI Map is any PAR Map converted to show Daily Light Integral per cell instead of instantaneous PPFD. With one tap you flip a finished PAR Map into a DLI Map, then set the daily lighting hours with a slider in half-hour steps. On iPhone it also shows the energy used in kWh for that interval. It's the tool for balancing yield against your electricity bill.
Build a PAR Map and enter your fixture's total watts. The app calculates Efficiency as the usable photon flux over your grow area divided by the watts drawn, giving you µmol per second per watt. That's the same number our calculators call efficacy, in µmol/J. It's a practical figure of merit. Run the same map for two fixtures and the higher number is doing more with your electricity. Just remember it measures usable light over your actual footprint, not the fixture's rated total.
Try it: Grow Light Efficacy Calculator
There's no single answer. It depends on your fixture, its wattage, and your plants' stage, so the best move is to measure. Make a PAR Map at one height, note the average PPFD and uniformity, then raise or lower the light and map again. Higher hanging spreads light wider and more evenly but drops intensity. Lower boosts intensity but creates hot spots. The map shows you the tradeoff in real numbers.
Try it: PPF to PPFD Calculator
Yes. Every PAR Map is stored right on your device, so you can create as many maps as you want and reopen any of them to edit its cell readings or rename it. To reorder your maps, long press one in the list and drag it. To delete a map, tap Edit, then Delete PAR Map. Nothing is uploaded to any server. This makes it easy to keep a map for each fixture or each grow, compare them later, and track how a change to your setup moved the numbers.
Light targets for plants
For cannabis and other high-light crops, seedlings and clones need gentler light, around 100–300 µmol/m²/s. In veg, aim for 400–600, and in flower push up to 600–1000. Leafy greens and most houseplants need far less. These are common starting points, so always check your specific plant's needs. Set your target as low and high thresholds in PPFD METER and the display pulses a different color the moment your light drifts out of range.
Try it: PPFD & DLI for Plants Calculator
It depends on the plant and its stage. As a rough guide, most houseplants do well on about 3–9 mol/m²/day, leafy greens and herbs on about 9–20, and fruiting and flowering crops on about 20–40. DLI ties intensity and photoperiod together, so a moderate PPFD run for long hours can match a strong PPFD run briefly. Look up your specific crop, then set the target in the app.
Try it: PPFD & DLI for Plants Calculator, PPFD to DLI Calculator
Multiply your PPFD by 3600, multiply by your daily lighting hours, then divide by one million. The 3600 turns per-second into per-hour, and dividing by a million converts micromoles to moles. For example, 600 PPFD for 18 hours is 600 times 3600 times 18 divided by 1000000, which is 38.9 mol/m²/day. PPFD METER does this math for you live as you change the photoperiod.
It depends on your plant and its stage, and it's really a DLI decision. Many growers run 18 hours in vegetative growth and 12 hours to trigger flowering, but the goal is hitting your plant's target DLI without overdoing intensity. Set your daily hours in the app, in half-hour steps, and watch how the DLI changes.
Try it: PPFD to DLI Calculator
Tomatoes are high-light crops. Typical ranges are about 300–500 µmol/m²/s in vegetative growth and 500–700 when flowering and fruiting, with a DLI of 17–29, then 29–40. Set your target as thresholds in PPFD METER and the color feedback keeps you in range as plants grow.
Try it: PPFD & DLI for Plants Calculator
Leafy greens like lettuce and spinach usually sit around 150–250 µmol/m²/s, with a DLI of about 9–14. Herbs like basil need more, about 200–350 and a DLI of 12–20. Set a threshold band in the app so you don't overshoot, and use a PAR Map to keep the whole tray evenly lit.
Try it: PPFD & DLI for Plants Calculator
Yes. Push PPFD too high and plants can show light stress, bleaching, or curling. Each step up in light can also bring a smaller gain, and it always brings a bigger power bill. Light works with temperature, CO2, and water, so all of them have to keep up. PPFD METER lets you set an upper threshold and shows you when your canopy crosses it.
Try it: PPFD & DLI for Plants Calculator
Look it up, then measure to it. A good starting search is your crop plus the words growing PPFD, for example 'tomatoes growing PPFD.' Once you know the target range, set it as your low and high thresholds in PPFD METER, and the display changes color to tell you at a glance whether your light is below, inside, or above your plant's target range.
Try it: PPFD & DLI for Plants Calculator
Planning a grow light
It depends on your tent size, the PPFD your plants need and how efficient the light is. As a rough guide, a 4 × 4 ft tent at 800 µmol/m²/s needs about 500 W from a modern LED at 2.8 µmol/J. Use the watts the light draws at the wall (its driver input power), not the number in its name. A light sold as "1000 W" often draws far less.
Try it: Grow Light Wattage Calculator
Multiply the watts it draws by the hours it runs, divide by 1000 to get kWh, then multiply by your price per kWh. A 300 W light running 18 hours a day at 0.29 per kWh costs about 1.57 a day, or about 47.63 a month, in whatever currency your bill uses. Dimming to your target PPFD is the easiest way to spend less.
There's no single best one. Plants grow well under a wide range of white and red-boosted mixes as long as they get enough light, so put intensity first. Warm whites carry more red, cool whites more blue, and a common recipe is a warm or neutral white with a boost of 660 nm deep red for flowering.
Try it: Grow Light Spectrum Calculator, Kelvin Mixing Calculator
Often not. A spot that looks bright to you may give a plant only a few mol/m²/day, while herbs and succulents need about 9–20. Measure the PPFD at the plant a few times through the day, then see how much a grow light has to add.
Try it: Supplemental Lighting Calculator
VPD, the vapor pressure deficit, is the air's drying pull. Too low and plants hardly transpire and mold moves in. Too high and they close their pores and growth stalls. Growers commonly aim for about 0.4–0.8 kPa for seedlings and clones, 0.8–1.2 kPa in veg and 1.2–1.6 kPa in flower.
Try it: VPD Calculator
Price, privacy and devices
Yes. Every measurement feature is completely free on iOS and Android. All the LUX, PPFD, and DLI reading, calibration, profiles, and PAR Maps work in the free version. PAR meters get pricey. Your phone doesn't have to be. The app is free with ads, and the paid options only remove those ads.
You never pay to unlock features. Every measurement feature is free. The paid options only remove ads and let you support development. There are three. Remove Ads is a one-time lifetime purchase, while Premium and Premium Plus are subscriptions that remove ads and support the project at different levels. Pick whichever feels right. You won't miss any feature either way.
To go ad-free, choose any of the three options: Remove Ads (a one-time purchase), Premium, or Premium Plus. Premium and Premium Plus are standard Google Play or App Store subscriptions, so you manage or cancel them anytime from your Google Play or Apple ID subscriptions screen. Remove Ads is a one-time purchase, so there's nothing to cancel. Our Terms & Conditions cover billing, renewals, and refunds.
No. Your profiles, thresholds, calibration factors, and saved PAR and DLI Maps all stay on your own device, and we never see them. The only way they leave your phone is through your own Google or iCloud backup, if you've turned that on, and that goes to your account, not to us. The app never reads your phone's location. It does use third-party services for usage statistics, crash reports and the ads in the free version, and these can tell roughly which country you're in. Our Privacy Policy has the details.
No. On iOS the app uses the front camera as a light meter, but it never saves or uploads an image. It only reads the camera's metadata to estimate brightness. No picture is captured or stored anywhere, on your phone or off it. Our Privacy Policy has the details.
PPFD METER is localized into 12 languages plus English: German, Spanish, French, Italian, Japanese, Korean, Dutch, Portuguese, Russian, Thai, Turkish, and Chinese. It follows your phone's language automatically. Technical terms like PPFD, DLI, and PAR stay in their standard form across every language, since those are the same for growers worldwide.
Yes. When you set up a PAR Map you can toggle between metric and imperial for your grow area dimensions, so you can enter your tent as centimeters or as inches and feet, whichever you think in. The light readings themselves, PPFD in µmol/m²/s and DLI in mol/m²/day, use the standard scientific units growers everywhere share.
On Android it runs on Android 8.0 and newer, on almost any phone with a built-in ambient light sensor, which is most of them. On iPhone it needs iOS 18 or later. If you're on a supported version, you're ready to measure right away.