Grow Light Wattage Calculator
How many watts do you need for your grow tent? Enter its size, the PPFD your plants need and how efficient the light is, and see the driver input power it takes. Already have a light? Switch to Check my light and see if it's enough.
How many watts do I need?
Watts = Target PPFD × Grow area (m²) ÷ Light on the canopy ÷ Efficacy (µmol/J)
Average PPFD = Driver input power (W) × Efficacy (µmol/J) × Light on the canopy ÷ Grow area (m²)
Working out grow light wattage is a lot like buying paint. The tent size is the size of the wall, the target PPFD is how thick a coat you want, and the light’s efficacy is how far each can goes. A bigger wall or a thicker coat needs more paint, and a better paint needs fewer cans. The calculator first works out how much light the plants need in total, the PPF in µmol/s, then divides it by the efficacy to get the watts. The result is the driver input power, what the light draws at the wall, not the number in its name. A light sold as “1000 W” often draws far less.
The number that matters most after the tent size is efficacy, measured in µmol/J. It counts how many photons a light makes for every watt it draws. A modern LED at 2.8 µmol/J gives the same light as a double-ended HPS at 1.9 µmol/J for about a third fewer watts. That’s why “watts per square foot” rules of thumb from the HPS days overshoot with LEDs. Copy the µmol/J from the light’s spec sheet. No spec sheet? The note under the field gives typical values for each kind of light. The Grow Light Efficacy Calculator works it out for a light you already have.
Not all of the light lands on your plants. Some hits the walls, some spills past the edge of the canopy, and some is lost along the way. The light on the canopy setting covers that. Reflective walls, like a grow tent’s, send most of it back to the plants, white walls lose more, and an open space loses the most. These are rough estimates, good for planning, and the light’s shape and hanging height move them too. One catch is that a spec sheet’s µmol/J is measured in a lab, where every photon counts. If you got your µmol/J from a PPFD reading in your own grow space instead, for example with the efficacy calculator, the losses are already in it. Set light on the canopy to 100% then, or you count them twice.
Not sure what target to use? The note under the field gives the typical range for each stage, from our plant data. For your exact plant, look up its range with the PPFD & DLI for Plants finder. Have a DLI target instead? Turn it into PPFD with the DLI to PPFD calculator first.
Already have a light? Check my light works the other way around. Enter its driver input power, and it shows the average PPFD you should get and how it compares to your target. If it’s short, it says roughly how many watts to add. If there’s light to spare, it shows how far you could dim it.
The result is an average over the whole area. The middle of the tent always reads higher than the corners, and a real light rarely matches its spec sheet exactly. Once the light is hung, measure it. PPFD METER reads PPFD with your phone, and its PAR Map walks you across the canopy point by point and shows the average, the weak corners and the usable PPF per watt your setup really delivers.
How many watts for a 4 × 4 ft grow tent? About 500 W at the wall for 800 PPFD, from a 2.8 µmol/J LED with reflective walls, or 485 W for a 120 × 120 cm tent. The table below gives the other common sizes and targets for the same light. A less efficient light needs more watts, so for your own light, use the calculator above.
| Tentcmft | 200PPFD | 400PPFD | 600PPFD | 800PPFD | 1000PPFD |
|---|---|---|---|---|---|
| 60 × 602 × 2 | 3030 | 6060 | 9095 | 120125 | 150155 |
| 60 × 1202 × 4 | 6060 | 120125 | 180185 | 240250 | 305310 |
| 90 × 903 × 3 | 7070 | 135140 | 205210 | 270280 | 340350 |
| 120 × 1204 × 4 | 120125 | 240250 | 365375 | 485500 | 605625 |
| 150 × 1505 × 5 | 190195 | 380390 | 565585 | 755780 | 945975 |
| 120 × 2404 × 8 | 240250 | 485500 | 725750 | 9701000 | 12101250 |