LUX to PPFD Calculator

Turn a LUX reading from any light meter into an estimated PPFD value. Pick your light below, and the calculator converts through its spectrum, since the same LUX can mean very different PPFD under different lights.

PPFD

400–700 nm

181

µmol m⁻² s⁻¹

ePPFD

400–750 nm

210

µmol m⁻² s⁻¹

How it's calculated

LUX measures light the way your eyes see it, and PPFD counts the photons plants use. The calculator takes the spectrum of the light you pick and reads it twice. Once through the eye's sensitivity curve, which gives its LUX, and once by counting its photons from 400 to 700 nm, which gives its PPFD, or to 750 nm for ePPFD, which adds the far red plants also use. The ratio of the two turns your number into the other one. That's why the light matters so much: deep red and blue make plenty of PPFD but very little LUX. This is a theoretical calculation, not a sensor reading. A phone's light sensor, its camera and a handheld LUX meter each see color a little differently from the eye's curve, most of all for deep red and blue, so each meter reports a slightly different reading. The PPFD METER app uses factors tested on each sensor it supports, so its readings are more precise.

Blue400–499 nm26%
Green500–599 nm31%
Red600–700 nm29%
Far Red701–750 nm14%
About the photon bars

The bars split this light's photons from 400 to 750 nm into four bands, so you can see where it puts its light. Plants respond to photons, and the eye mostly to green and yellow, which is why two lights with the same LUX can drive photosynthesis very differently.

About the chart

The colored shape is the light's spectrum, scaled to its own peak. The dashed line is the eye's sensitivity curve, the one every LUX reading is weighed by. It peaks in yellow-green at 555 nm and falls almost to nothing in deep blue and deep red. Light under the curve counts fully toward LUX. Plants still use the light outside it, but LUX hardly sees it.

How to convert LUX to PPFD

PPFD (µmol m⁻² s⁻¹) = LUX × the light's photons from 400–700 nm ÷ its lumens. ePPFD: the same, with photons from 400–750 nm

Every light has its own LUX to PPFD conversion factor, and it comes from the light’s spectrum. Sunlight works out to about 55 LUX per µmol m⁻² s⁻¹, a 3500K white LED about 73, high-pressure sodium about 85, ceramic metal halide about 58, halogen about 51 and a 4000K fluorescent tube about 75. Pick your light and the calculator works out its rate from its spectrum and draws that spectrum against the eye’s sensitivity curve, so you can see why.

Next to PPFD you also get ePPFD, which counts photons up to 750 nm and so adds the far red plants also use. Sunlight carries a lot of far red, so 10000 LUX of daylight is about 181 PPFD but 210 ePPFD; most white LEDs carry little, so their two numbers sit close together.

Narrowband red and blue LEDs are the extreme case, at about 8 LUX per µmol m⁻² s⁻¹ for a 450 nm blue LED and about 10 for a 660 nm red one. A 730 nm far-red LED goes furthest. It’s almost invisible to the eye, so a reading of a few LUX can mean a large ePPFD. LUX measures how bright light looks to the human eye, and the eye barely notices deep red and blue. So a red or blue grow LED can read low in LUX while still delivering plenty of PPFD to your plants. A few nanometers’ shift in an LED’s peak moves its rate a lot, so treat single-color LEDs as a ballpark.

These are estimates from typical spectra, not a lab measurement of your fixture. The LEDs are measured spectra of widely used horticultural LEDs, sunlight is standard daylight, and the lamps are typical spectra for their kind. Your own light’s exact spectrum shifts the real ratio a little, and every sensor sees color its own way, so a phone or a handheld LUX meter can read differently too. For live, per-light readings, PPFD METER converts LUX to PPFD for you with factors tested on each sensor it supports, and you can pair it with a Bluetooth LUX meter like the UNI-T UT383BT for steadier, repeatable readings.

If your meter reads in foot-candles instead of LUX, switch to Imperial above. 1 foot-candle ≈ 10.76 LUX, and the calculator converts for you either way; PPFD always comes out in µmol m⁻² s⁻¹ regardless of which unit you enter.